Chevrolet Cruze manuals

Chevrolet Cruze Repair Manual: Rear Compartment Lid Emblem/Nameplate Replacement (VCDi AT)

Chevrolet Cruze Repair Manual / Body hardware and trim / Exterior Trim / Rear Compartment Lid Emblem/Nameplate Replacement (VCDi AT)

Rear Compartment Lid Emblem Assembly

Rear Compartment Lid Emblem Assembly

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Use a Heat Gun or equivalent to remove the old emblem. Clean all adhesive from the rear compartment panel and wipe the surface dry with a clean lint-free towel prior to installing the new emblem.
  3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
  4. Close the rear compartment   lid prior to adhesion.
  5. Using the palm of the hand, wet out the emblem to the rear compartment lid to ensure full adhesion of the emblem is made.

Rear Compartment Lid Emblem/Nameplate Replacement (Diesel)

Rear Compartment Lid Emblem Assembly

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength
  2. Use a Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from the rear compartment panel and wipe the surface dry with a clean lint-free towel prior to installing the new nameplate.
  3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
  4. Close the rear compartment  lid prior to adhesion
  5. Using the palm of the hand, wet out the emblem to the rear compartment lid to ensure full adhesion of the emblem is made.

Radiator Upper Grille Replacement

Preliminary Procedure

Preliminary Procedure

Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement.

  1. Radiator Upper Grille Clip (Qty: 4)
  2. Radiator Upper Grille Screw (Qty: 8)

Caution: Refer to Fastener Caution in the Preface section.

Tighten 2.5 N·m(22 lb in)

  1. Radiator Upper Grille Assembly

Radiator Lower Grille Replacement

Preliminary Procedure

Preliminary Procedure

Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement.

  1. Radiator Lower Grille Screw (Qty: 4)

Caution: Refer to Fastener Caution in the Preface section.

Tighten 2.5 N·m(22 lb in)

  1. Radiator Lower Grille Assembly
Rear Compartment Lid Emblem/Nameplate Replacement (VCDi)
Rear Compartment Lid Emblem Assembly Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section. Procedure The part and surface should be 21°C (70°F) prior to installati ...

Water Management Description and Operation
Plenum Water Flow Direction and Cleaning A large percentage of water will flow off the windshield area into the plenum chamber drain system and then down the outside on the plenum to the underside ...

Other materials:

Installation Procedure
Cut the front compartment front rail in corresponding locations to fit the remaining original panel. The sectioning joint should be trimmed to allow a gap of one-and-one-half-times the metal thickness at the sectioning joint. Create a 50 mm (2 in) backing plate from the unused porti ...

Dual Phase Steel
This information provides repair recommendations and general guidelines for steel classified as Dual Phase Steel (Dual Phase Steel with a tensile strength up to and including 800 MPa), also known as DP. General Motors recommends the following when repairing or replacing this type of steel du ...

Restraints
Specifications Module Power, Ground, and MIL Front Impact Sensor, Retractors, and Driver/Passenger Air Bags Side Impact Sensors and Side/Roof Air Bags Air Bag Indicator and Disable Switch (C99) ...

© 2017-2021 Copyright www.crion.site