Chevrolet Cruze manuals

Chevrolet Cruze Repair Manual: Power Steering Fluid Reservoir Replacement

Chevrolet Cruze Repair Manual / Steering / Power Steering / Power Steering Fluid Reservoir Replacement

Preliminary Procedure

Preliminary Procedure

  1. Remove as much power steering fluid from the remote power steering fluid reservoir as possible.
  2. Place drain pans under the vehicle as needed.
  1. Hose Clamp

Procedure

  1. Compress the power steering fluid reservoir outlet and inlet hose clamp from the power steering fluid reservoir.
  2. Remove outlet and inlet hose from power steering fluid reservoir.
  1. Power Steering Fluid Reservoir Screw

Caution: Refer to Fastener Caution in the Preface section.

Tighten 9 N·m (80 lb in)

  1. Power Steering Fluid Reservoir

Procedure

Fill and bleed the power steering system. Refer to Power Steering System Bleeding.

Tip

Clean any excess power steering fluid from the vehicle.

Power Steering Pump Pulley Replacement

Preliminary Procedure

Preliminary Procedure

Remove the power steering pump. Refer to Power Steering Pump Replacement.

Power Steering Pump Pulley

Procedure

  1. Use CH 25034-D Pulley Remover to remove the  power steering pump pulley.
  2. Use CH 25033-C Pulley Installer to install the power steering pump pulley.

Special Tools

For equivalent regional tools, refer to Special Tools.

Power Steering Pump Replacement

Preliminary Procedure

Preliminary Procedure

  1. Remove the power steering pump belt. Refer to Power Steering   Pump Belt Replacement
  2. Place drain pans under the vehicle as needed.
  1. Power Steering Gear Inlet Hose Hollow Screw

Caution: Refer to Fastener Caution in the Preface section.

Tighten 21 N·m (16 lb in)

  1. Power Steering Gear Inlet Hose
  2. Power Steering Reservoir Outlet Hose
  3. Power Steering Pump Bolt (Qty: 2)

Tighten 22 N·m (17 lb ft)

  1. Power Steering Pump

Procedure

Fill and bleed the power steering system. Refer to Power Steering System Bleeding.

Tip

Clean any excess power steering fluid from the vehicle.

Power Steering Pump Bracket Replacement

Preliminary Procedure

Preliminary Procedure

Remove the power steering pump. Refer to Power Steering Pump Replacement.

  1. Power Steering Pump Bracket Screw

Caution: Refer to Fastener Caution in the Preface section.

Tighten 22 N·m (16 lb ft)

  1. Power Steering Pump Bracket
Checking and Adding Power Steering Fluid
Caution: When adding fluid or making a complete fluid change, always use the proper power steering fluid. Failure to use the proper fluid will cause hose and seal damage and fluid leaks. Clean ...

Steering Linkage Outer Tie Rod Replacement
Preliminary Procedure Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation. Steering Linkage Tie Rod Nut Caution: Refer to Fastener Caution in the Preface ...

Other materials:

Ignition Positions (Key Access)
The ignition switch has four different positions. Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key. Use the correct key, make sure it is all the way in, and turn it only with your hand. If the key cannot be turned by hand, see yo ...

Securing Child Restraints (Rear Seat)
When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle. If the child restraint has the LATCH system. Do not secure a child seat in a position without a top tether anchor if a national ...

Installation Procedure
Create 5 x 18 mm (4/16 x 11/16 in) slots for MIG-Brazing along the edges of the front wheelhouse front panel as noted from the original panel. Create a 5 x 18 mm (4/16 x 11/16 in) slot for MIG-Brazing where front wheelhouse front panel  and front wheelhouse overlap. C ...

© 2017-2021 Copyright www.crion.site