Chevrolet Cruze manuals

Chevrolet Cruze Repair Manual: Mirrors

Specifications

Inside Rearview Mirror Schematics

Inside Rearview Mirror Schematics

Outside Rearview Mirror Schematics

Outside Rearview Mirror Schematics

Outside Rearview Mirror Replacement

Outside Rearview Mirror Replacement

Preliminary Procedure

Preliminary Procedure

  1. Remove the front side door trim. Refer to Front Side   Door Trim Replacement.
  2. Remove the front side door upper trim cover. Refer to Front Side Door Upper Trim Cover Replacement.
  1. Outside Rearview Mirror Mount Plate Bolt (Qty: 3)

Caution: Refer to Fastener Caution in the Preface section.

Tighten 9 N·m (80 lb in)

  1. Outside Rearview Mirror

Tip

Disconnect electrical connector.

Outside Remote Control Rearview Mirror Switch Replacement

Preliminary Procedure

Preliminary Procedure

  1. Remove front side door trim. Refer to Front Side  Door Trim Replacement.
  2. Remove front side door window switch bezel. Refer to Front Side Door Window Switch Bezel Replacement.
  1. Side Window Switch Bezel
  2. Power Mirror Switch

Procedure

  1. Using a plastic pry tool, gently pry on the sides to release the switch.
  2. Disconnect the electrical connector.

Outside Rearview Mirror Motor Replacement

Preliminary Procedure

Preliminary Procedure

Remove the outside rearview mirror glass. Refer to Outside Rearview Mirror Glass Replacement.

  1. Outside Rearview Mirror Motor Bolt (Qty: 3)

Caution: Refer to Fastener Caution in the Preface section.

Tighten 3 N·m (27 lb in).

  1. Outside Rearview Mirror Motor

Tip

Disconnect the electrical connector.

Outside Rearview Mirror Glass Replacement

Warning: Refer to Glass and Sheet Metal Handling Warning in the Preface

Warning: Refer to Glass and Sheet Metal Handling Warning in the Preface section.

Outside Rearview Mirror Glass

Procedure

  1. Release the mirror glass backing from the mirror housing by pulling outward.

Tip

Disconnect the power wire harness electrical connector.

Outside Rearview Mirror Housing Replacement

Preliminary Procedure

Preliminary Procedure

Remove outside rearview mirror glass. Refer to Outside Rearview Mirror Glass Replacement.

  1. Outside Rearview Mirror Housing Screw (Qty: 4)

Caution: Refer to Fastener Caution in the Preface section.

Tighten 2.5 N·m (22 lb in)

  1. Lower Outside Rearview Mirror Housing Screw

Tighten 2.5 N·m (22 lb in)

  1. Outside Rearview Mirror Housing

Tip

Disconnect electrical connector.

Inside Rearview Mirror Replacement

Preliminary Procedure

Preliminary Procedure

  1. Remove the outside moisture cover. Refer to Windshield Outside Moisture Sensor  Cover Replacement
  2. Adjust the mirror to the full upward position.

Inside Rearview Mirror Bolt

Caution: Refer to Fastener Caution in the Preface section.

Tighten 8 N·m (80 lb in)

Inside Rearview Mirror

Tip

Slide the mirror in an upward motion in order to remove.

Interior Lamps Dimming
This group includes lamps which may dim. This group may use a combination of vacuum fluorescent illumination, LEDs and incandescent lamps HVAC control module, head assembly Rear HVAC control ...

Vehicle Access
Specifications Door Lock/Indicator Schematics Door Control Module Schematics Release Systems Schematics Fuel Tank Filler Door Lock Actuator Replacement ...

Other materials:

Installation Procedure
Remove rear end upper panel extension (1) from service part. Cut the body side inner panel in corresponding locations to fit the remaining original panel. The sectioning joint should be trimmed to allow a gap of one-and-one-half-times the metal thickness at the sectioning jo ...

Windshield Wiper Arm Replacement
Windshield Washer Arm Finish Cap Tip Use a small flat-bladed tool to remove finish cap. Special Tools BO-6626 Wiper Arm Puller For equivalent regional tools, refer to Special Tools. Windshield Washer Arm Nut Caution: Refer to Fastener Caution in the Preface section. Procedure ...

Fuses and Circuit Breakers
The wiring circuits in the vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of damage caused by electrical problems. To check a fuse, look at the silver-colored band inside the fuse. If the band is broken or melted, repla ...

© 2017-2021 Copyright www.crion.site