Chevrolet Cruze manuals

Chevrolet Cruze Repair Manual: Driver or Passenger Seat Replacement

Chevrolet Cruze Repair Manual / Seats / Seat Hardware, Trim, and Upholstery / Driver or Passenger Seat Replacement

Removal Procedure

Warning: Refer to SIR Warning in the Preface section.

Warning: When carrying a live inflator module, make sure the bag

Warning: When carrying a live inflator module, make sure the bag opening is pointed away from you. This minimizes the chance of injury in the case of an accidental deployment. Never carry the inflator module by the wires. Never carry the inflator module by the connector on the underside of the module.

Make sure that the bag and trim cover are facing up whenever you place a live inflator module on any surface. This is necessary to provide a free space for the bag to expand in the unlikely event of accidental deployment. Never rest the steering column assembly on the steering wheel with the inflator module face down, and the column vertical. This may result in personal injury.

  1. Disable the supplemental inflatable restraint (SIR) system. Refer to SIR  Disabling and Enabling.
  2. Remove the front seat outer recliner upper finish cover (1).
  3. Unscrew the bolt (2)
  4. Remove the seat belt (3) from the front seat.

  1. Unscrew the 2 bolts (1).
  2. Disconnect the wiring harness plug (2) from the belt buckle.
  3. Release and disconnect the wiring harness plug (3) front seat.
  4. Remove the front seat (4) from the guide in front.

Installation Procedure

  1. Perform the front seat track synchronization. Refer to Front Seat  Track Synchronization.
  2. Install the front seat (4) to the guide in front.
  3. Connect and latch the wiring harness plug (3) front seat.
  4. Connect the wiring harness plug (2) from the belt buckle.

Caution: Refer to Fastener Caution in the Preface section.

  1. Tighten the 2 bolts (1).

Tighten 45 N·m (33 lb in)

  1. Install the seat belt (3) to the front seat.
  2. Tighten the bolt (2).

Tighten 9 N·m (80 lb in)

  1. Install the front seat outer recliner upper finish cover (1).
  2. Enable the SIR system. Refer to SIR Disabling and Enabling.

Front Seat Outer Recliner Upper Finish Cover Replacement

  1. Front Seat Outer Recliner Upper Finish Cover Assembly

Front Seat Adjuster Replacement

  1. Front Seat Outer Recliner Upper Finish Cover
  2. Front Seat Adjuster Bolt

Caution: Refer to Fastener Caution in the Preface section.

Tighten 20 N·m(15 lb in)

  1. Front Seat Adjuster
Seat Hardware, Trim, and Upholstery
Specifications ...

Front Seat Track Synchronization
The fore/aft manual adjuster is composed of an inboard track assembly (5), and outboard track (4) assembly, and an adjuster handle (1). Each track assembly is made of an upper track (2) and a ...

Other materials:

Front Bumper Impact Bar Replacement
Removal Procedure Warning: Refer to Approved Equipment for Collision Repair Warning in the Preface section. Warning: Refer to Glass and Sheet Metal Handling Warning in the Preface section. Disable the SIR System. Refer to SIR  Disabling and Enabling. Disconnect the negative battery ...

Winter Driving
Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 0°C (32°F) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads c ...

Installation Procedure
Create 6 x 20 mm (4/16 x 11/16 in) slots for MIG-brazing along the upper edges of the service panel as noted from the original panel. Clean and prepare the attaching surfaces for brazing and spot welding. Position the body lock pillar inner panel on the vehicle. Verify the ...

© 2017-2022 Copyright www.crion.site