Chevrolet Cruze manuals

Chevrolet Cruze Repair Manual: Door Ajar Indicator Description and Operation

Chevrolet Cruze Repair Manual / Body systems / Vehicle Access / Door Ajar Indicator Description and Operation

Door Ajar Indicator System Components

The door ajar indicator system consists of the following components:

Driver Door Ajar

The driver window motor (RPO AXG) or driver window switch (RPO AEC) receives a discrete input from the driver door ajar switch within the driver door latch to indicate the status of the door. The window motor or window switch then communicates this status via Local Interconnect Network (LIN) bus to the BCM. The BCM communicates this information to the instrument cluster via low speed bus. The instrument panel cluster, upon receipt of this GMLAN message, will illuminate the appropriate door ajar message in the driver information center and also send a GMLAN message to the radio to activate the door ajar audible warning when the vehicle speed is greater than 8 km/h (5 MPH).

Passenger Door Ajar

The passenger window switch receives a discrete input from the passenger door ajar switch within the passenger door latch to indicate the status of the door. The window switch then communicates this status via LIN bus to the BCM. The BCM communicates this information to the instrument cluster via low speed bus. The instrument panel cluster, upon receipt of this GMLAN message, will illuminate the appropriate door ajar message in the driver information center and also send a GMLAN message to the radio to activate the door ajar audible warning when the vehicle speed is greater than 8 km/h (5 MPH).

Left Rear Door Ajar And Right Rear Door Ajar

The body control module (BCM) (without power rear windows) or the left and right rear window switches (with power rear windows AED) receive discrete inputs from both the rear door latches and the rear compartment lid latch to indicate the status of the doors and rear compartment lid. The BCM or window switches then communicate this status to the instrument cluster via GMLAN message. The instrument panel cluster, upon receipt of this GMLAN message, will illuminate the appropriate door ajar message in the driver information center and also send a GMLAN message to the radio to activate the door ajar audible warning when the vehicle speed is greater than 8 km/h (5 MPH).

Fuel Fill Door Description and Operation

Fuel Door Release System Components

The locking and unlocking of the fuel door is a function of the power door lock system. The fuel door release actuator shares the circuit with the driver door latch. The body control module (BCM), upon receipt of a lock switch lock or unlock signal, will switch the appropriate door latch, as well as a fuel filler door release actuator control circuits to B+ voltage. The opposing side of the door latch and fuel filler door release actuator is connected to ground provided by the BCM through the other the door latch control circuits, along with the fuel filler door release actuator, will lock or unlock as commanded.

Rear Side Door Outside Handle Rod Adjustment
Removal Procedure Remove the rear door water deflector as needed. Refer to Rear Side Door Water Deflector Replacement. Use a flat-head tool to open the clip from the threaded rod connecti ...

Luggage Compartment Description and Operation
Rear Compartment Lid Release System Components Body control module (BCM) Exterior rear compartment lid release switch Rear compartment lid release actuator Rear compartment lid release relay ...

Other materials:

Removal Procedure
Warning: Refer to Approved Equipment for Collision Repair Warning in the Preface section. Warning: Refer to Collision Sectioning Warning in the Preface section. Warning: Refer to Glass and Sheet Metal Handling Warning in the Preface section. Disable the SIR System. Refer to SIR  Dis ...

Instrument Panel Upper Compartment Replacement
Instrument Panel Upper Compartment Screw (Qty: 2) Caution: Refer to Fastener Caution in the Preface section. Procedure Before removing the instrument panel upper compartment screws, remove mat. Tighten 2.5 N·m (23 lb in) Instrument Panel Upper Compartment Assembly ...

Rear Spring Insulator Replacement
Removal Procedure Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle. Support the rear axle with a tall jack stand near the shock absorber. Remove the lower shock bolt. Refer to Shock Absorber Replacement. Using the tall jack stands, slowly lower the rear a ...

© 2017-2021 Copyright www.crion.site