Chevrolet Cruze manuals

Chevrolet Cruze Repair Manual: Brake Pedal Position Sensor Calibration

Chevrolet Cruze Repair Manual / Body systems / Lighting / Brake Pedal Position Sensor Calibration

Calibration Criteria

Note: Do not apply the brake pedal during the brake pedal position (BPP) sensor calibration procedure. Any movement of the brake pedal during this procedure will cause the calibration procedure to fail. If this occurs, the sensor calibration must be repeated.

Brake pedal position (BPP) sensor calibration must be performed after the sensor or body control module (BCM) have been serviced. The calibration procedure will set the sensor home value. This value is used by the BCM to determine the action of the driver applying the brake system and to provide this information to the vehicle subsystems via serial data.

Calibration Procedure

  1. Apply the parking brake.
  2. Place the transmission in the PARK position.
  3. Install a scan tool.
  4. Clear all BCM DTCs before proceeding.
  5. Navigate to the Vehicle Control Systems menu.
  6. Select Module Setup menu item.
  7. Select BCM menu item
  8. Select the BPP Sensor Calibration procedure and follow the directions displayed on the screen.

Brake Pedal Position Sensor Replacement

Preliminary Procedure

Preliminary Procedure

Remove the instrument panel lower trim pad cover. Refer to Instrument Panel Lower Trim Pad Cover Replacement.

  1. Brake Pedal Position Sensor Bolt

Caution: Refer to Fastener Caution in the Preface section.

Tighten 2 N·m (18 lb in)

  1. Brake Pedal Position Sensor

Procedure

  1. Disconnect 1. the electrical connector.
  2. Calibrate the brake pedal position sensor. Refer to Brake Pedal Position Sensor Calibration.

Headlamp Switch Replacement (Right Hand Drive)

Headlamp Switch Assembly

Headlamp Switch Assembly

Procedure

  1. Open the compartment to remove the headlamp switch.
  2. Disconnect the electrical connection.

Fog Lamp Switch Replacement (Right Hand Drive)

Fog Lamp Switch

Fog Lamp Switch

Procedure

  1. Disconnect   the electrical connection.
  2. Squeeze tabs on switch to unsnap from housing bracket.

Hazard Warning Switch Replacement

Preliminary Procedure

Preliminary Procedure

Remove instrument panel accessory bezel. Refer to Instrument Panel Accessory Bezel Replacement.

Hazard Warning Switch

Procedure

  1. Disconnect the electrical connection.
  2. Unsnap switch from instrument panel accessory bezel.

Instrument Panel Lamp Dimmer Switch Replacement (Right Hand Drive)

Instrument Panel Lamp Dimmer Switch

Instrument Panel Lamp Dimmer Switch

Procedure

  1. Disconnect  electrical connector.
  2. Squeeze tabs on switch to unsnap from housing bracket.

Reading Lamp Bulb Replacement

  1. Dome and Reading Lamp Lens
  2. Reading Lamp Bulb (Qty: 2)

Dome and Reading Lamp Lens Replacement

  1. Dome and Reading Lamp Lens

Dome Lamp Replacement

Preliminary Procedure

Preliminary Procedure

Lower the headliner enough to gain access to the dome lamp housing. Refer to Headlining Trim Panel Replacement.

  1. Dome Lamp Lens
  2. Dome Lamp Switch Bezel
  3. Dome Lamp Housing Assembly

Procedure

  1. Carefully use a flat-bladed tool, and release the tabs retaining the dome  lamp to the headliner.
  2. Disconnect the electrical connector.

Dome Lamp Bulb Replacement

  1. Dome and Reading Lamp Lens
  2. Dome Lamp Bulb
Lighting
Specifications Headlights/Daytime Running Lights (DRL) Schematics Interior Lights Schematics ...

Headlamp Replacement
Preliminary Procedure Remove the front bumper fascia upper bracket. Refer to Front Bumper Fascia Replacement. Headlamp Screw (Qty: 4) Caution: Refer to Fastener Caution in the Preface se ...

Other materials:

Radio Reception
Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory p ...

Front Brake Rotor Replacement
Special Tools CH-41013 Rotor Resurfacing Kit CH-42450-A Wheel Hub Resurfacing Kit For equivalent regional tools, refer to Special Tools. Removal Procedure Warning: Refer to Brake Dust Warning in the Preface section. Raise and support the vehicle. Refer to Lifting  and Jacking ...

Interior Lamps Dimming
This group includes lamps which may dim. This group may use a combination of vacuum fluorescent illumination, LEDs and incandescent lamps HVAC control module, head assembly Rear HVAC control module, head assembly Radio Rear seat audio The instrument panel cluster The PRNDL lamp, wit ...

© 2017-2021 Copyright www.crion.site